Radio Shack 3-DVD Changer Manual do Utilizador descarregar pdf

AT&T IR U-verse

TV Remote Control

User Guide

Installing Batteries

The remote control requires

two AA size (1.5V) Alkaline

batteries to work.

Tips: replace the batteries

every nine months for opti-

mum performance.

1. On the back of the remote

control, press the battery

cover tab forward, lift and

remove the battery cover.

2. Insert two (2) AA-size bat-

teries, matching the + and

– symbols with the bat-

tery pictures.

3. Put the battery cover back

on and test the remote

control by pressing the

AT&T key. The AT&T key

should light up to indicate

that batteries are inserted

properly.

Controlling Other

Devices

In order to control other de-

vices with your U-Verse TV

Remote Control, you need to

tell the remote control what

types of devices you have.

Section 1 guides you through

the steps needed to do this.

When you complete Section 1,

the volume and channels will

always work on the U-verse

TV Receiver no matter what

mode you are in. If you want

to change this or allow the

POWER key to affect multiple

devices then you can also fol-

low the steps in Section 2. If

you’d like to reset any of the

settings then you can go to

Sections 3 and 4.

1. Programming the

remote to control

other devices

To use the U-verse TV remote

control for your other devices,

you will need to program one

or more of the TV, DVD or AUX

buttons at the top of the re-

mote control. There are two

ways to do this. If your device

is listed in the Manufacture

Code List at the end of this

Manual, you can use section

A. If your device is not listed,

you will need to use section

Note:

The AUX button may be pro-

grammed to operate a VCR,

Home Theater In A Box (HTIB),

Receiver or Amplifier.

A. Manually

Use the following steps to

program the TV, DVD or AUX

mode keys:

1. Power on the device you

want to program

2. Locate the 4-digit set-up

code for the device you

want to program from the

Manufacture Code List in

this manual. If your device

is not listed you will need

to use section B on “Using

the Automatic Search”. If

there are multiple codes

listed for your device, you

may need to repeat steps

2 through 7 to find the

correct one.

3. Press and hold the appro-

priate mode key you want

to assign to this device

(TV, DVD or AUX) on the

remote control

4. While holding the mode

key, press the OK key

5. Release both the mode

key and the OK key

– All the mode keys should

flash twice

– You’ll now have 10 sec-

onds to start step 6

6. Enter the appropriate 4-

digit set-up code for your

device (from the Manufac-

ture Code List) by pressing

the number keys (0-9) on

the remote control

– If the mode key flashes

three times, then a correct

code has been entered.

– If the mode key gives a

long flash, then an invalid

code has been entered.

Start over at step 3.

– If all the mode keys give

a long flash, then the re-

mote control has timed-

out. Start over at step 3

7. Point the remote control

at the programmed de-

vice and press the power

key once

– The device should turn

off

– If it does not turn off,

repeat steps 2 through 6

trying each code for your

brand until you find the

correct code

8. Repeat steps 1 through 7

to program another de-

vice.

Note: If you are interrupted

while you are programming,

the remote control may time-

out before you complete the

code set-up and you will

need to start over. This is in-

dicated by a red flash of the

mode keys.

Now that your devices are pro-

grammed, you can press the

appropriate mode key on the

remote control to work with

the selected device. To use

the remote control for your U-

verse TV Receiver again, press

the AT&T mode key.

Combination Devices Note:

If you have an integrated or

combination unit, such as a

TV/DVD unit, each compo-

nent of the unit needs to be

programmed separately. In

the Manufacture Code List for

these devices there will be

codes for all components of

the combination unit. They

can be distinguished as fol-

lows:

- TV codes start with a “1”

- DVD codes start with a “2”

- AUX codes start with a “3”

For some combination devic-

es, the original remote control

may be required to switch be-

tween the components.

B. Using the

Automatic Search

You can search the remote

control memory for your 4

digit manufacture device

code. You will need to use

this function if the code for

your device is not listed in the

Manufacture Code List.

1. Turn on the device you

wish to program

2. Point the remote control

at the device

3. Press and hold the appro-

priate mode key you want

to assign to this device

(TV, DVD or AUX) on the

remote control

4. While holding the mode

key, press the OK key

5. Release both the mode

key and the OK key

– All the mode keys should

flash twice

– You’ll now have 10 sec-

onds to start step 6

6. Enter 922 by pressing the

number keys on the re-

mote control

– The selected mode key

will flash twice indicating

correct entry

7. For TV or DVD modes press

and release the PLAY key

– For AUX searching only,

press and release the

PLAY key then press

1 for VCR

2 for Receiver/Tuner

3 for Amplifier

4 for Home Theater In A

Box (HTIB)

– The AUX mode keys will

flash twice indicating cor-

rect entry

8. Now press the FF button

multiple times until the

device turns off

9. Press the ENTER key (bot-

tom right) to save the code

on the remote control

10. Check to make sure the

code works by pressing

the mode key, then the

power button, to turn the

device back on. If this

does not work, start again

at step 2.

11. Now that your devices

are programmed, you

can press the appropri-

ate mode key on the re-

mote control to work with

the selected device. To

use the remote control

for your AT&T U-verse TV

Receiver again, press the

AT&T mode key.

Note:

– If any other key is pressed

except PLAY, ENTER, POWER,

EXIT, REW, FF, or number keys

1 to 4, the selected mode key

will give a long red flash (er-

ror message) and the remote

control will return to normal

operation and you will need

to start over.

– If you are interrupted while

you are programming, the re-

mote control may time-out

before you complete the code

set-up and you will need to

start over. This is indicated by

a red flash of the mode keys.

2. Setting up your

Volume, Channel

and Power Options

The default for your power,

volume and channel con-

trols send the codes to the

U-verse TV receiver no matter

what mode you are in. Thus,

in DVD mode, the volume still

controls the U-verse TV re-

ceiver, etc. If you would like

to change this, follow these

instructions:

A. Volume Control

Set-Up Options

The volume commands are

always sent to the U-verse

TV receiver until the TV mode

key is programmed. Then the

volume commands are sent

to the TV from all mode keys.

If you’d like the volume com-

mands to still be sent to just

one device, but that it be a

different device (for example

a home theater setup) then

follow the instructions in Sec-

tion I. If you’d like the volume

commands sent to different

devices depending on which

mode you are in then go to

Section II.

I. Volume Always Con-

trols the same Device

1. Press and hold the AT&T

key on the remote control

2. While holding the AT&T

mode key, press the OK

key

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 955 by pressing the

number keys on the re-

mote control

– The AT&T key will flash

twice indicating correct

entry

5. Press the mode key that

you want to always receive

the volume commands

– The selected mode key

will flash three times indi-

cating successful assign-

ment and return to normal

operations

The volume commands will

now go to the selected device

no matter what mode you are

in.

II. Volume Control

Depends on Device

Selected

The volume setting can also

be re-configured to inde-

pendently control the volume

associated with each device.

(e.g. In AUX mode the receiver

controls the audio; In TV mode

the TV controls the audio)

1. Press and hold the AT&T

key on the remote control

2. While holding the AT&T

mode key, press the OK

key

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 955 by pressing the

number keys on the re-

mote control

– The AT&T key will flash

twice indicating correct

entry

5. Press the ENTER key

– The AT&T key will flash

three times indicating suc-

cessful assignment and

returns to normal opera-

tions

B. Channel Selection

Set-Up Option

By default the remote con-

trol will always send chan-

nel commands to the U-verse

TV receiver no matter what

mode you are in. This will pre-

vent accidental TV channel

changes while in TV, DVD or

AUX modes.

There are two ways you can

change this: I) Have channel

commands always go to a

single device other than the

U-verse TV receiver; II) Have

channel commands go to dif-

ferent devices when in differ-

ent modes (e.g., When in TV

mode the channel commands

go to the TV, when in DVD

mode the channel commands

go to the DVD player, etc.).

See the appropriate section

for each.

I. Channel Always

Controls the Same Device

1. Press and hold the AT&T

key on the remote control

2. While holding the AT&T

mode key, press the OK

key

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 966 by pressing the

number keys on the re-

mote control

– The AT&T key will flash

twice indicating correct

entry

5. Press the mode key that

you wish the channel

commands to always go

– The selected mode key

will flash three times indi-

cating success and return

to normal operations.

The channel commands will

now go to the selected device

no matter what mode you are

in.

II. Channel Control

Depends on Device

Selected

1. Press and hold the AT&T

key on the remote control

2. While holding the AT&T

mode key, press the OK

key

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 966 by pressing the

number keys on the re-

mote control

– The AT&T key will flash

twice indicating correct

entry

5. Press the Enter key

– The AT&T key will flash

three times indicating

successful assignment

and return to normal op-

erations.

If you press any key other

than the mode keys or EN-

TER, the AT&T key will give a

long red flash and the remote

control will return to normal

operation. Should the remote

control time-out before you

complete the procedure you

will need to start over.

C. Power Control

Set-Up Options

By default, the POWER key

only powers on or places your

U-verse TV receiver in stand-

by mode. Once you have pro-

grammed the TV mode key,

the TV and U-verse TV receiver

will both be powered on/off

simultaneously. You also have

the option to turn on/off TV,

DVD and AUX mode devices

individually by pressing the

applicable mode key then the

POWER key.

I. To Have Multiple

Devices Power Off with

the Power Key

If you would like other devices

to be powered on/off simulta-

neously with the POWER key,

then follow these instructions

for the additional devices (for

a total of 4).

1. Press and hold the AT&T

key on the remote control

2. While holding the AT&T

mode key, press the OK

key

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 977 by pressing the

number keys on the re-

mote control

– The AT&T key will flash

twice indicating correct

entry

5. Press the AT&T key on the

remote control

– The AT&T key will flash

twice indicating correct

entry

6. Press the TV key on the

remote control

– The TV key will flash

twice indicating correct

entry

7. Press each additional

mode key that you wish to

include such as the DVD

key or AUX key

– Each selected mode key

will flash twice indicating

correct entry

8. Press the ENTER key to

complete

– The last mode key se-

lected will flash three

times indicating success-

ful assignment and return

to normal operations

Note:

If any key is pressed except

the mode keys and ENTER,

the AT&T key will give a long

red flash and the remote con-

trol will return to normal op-

eration. Should the remote

control time-out before you

complete the procedure you

will need to start over.

If the devices that you have

programmed to turn ON/OFF

at the same time get out of

sync so that some turn ON

and others turn OFF, you will

need to manually turn OFF

the out of sync devices and

then press the POWER key to

turn them all back ON. It is

important to point the remote

directly toward the devices for

this to work properly.

To change the number of de-

vices controlled by the POW-

ER key, you must start at Step

1 and continue until all de-

sired devices have been pro-

grammed.

3. Changing and

Removing Codes

A. Mode

Deactivation

To deactivate a mode key, fol-

low these steps:

1. Press and hold the mode

key (TV, DVD or AUX) that

you’d like to deactivate on

the remote control

2. Without releasing the cho-

sen mode key, press and

hold the OK key simulta-

neously

3. Release both the mode

key and the OK key

– All the mode keys should

flash twice

4. Enter the appropriate 4-

digit code from the list

below depending on the

mode you are deactivat-

ing:

– TV: 1254

– DVD: 2254

– AUX: 3254

– The mode key will flash

three times indicating cor-

rect entry and return to

normal operation

– When an invalid code

is entered, the selected

mode key will give a long

flash to indicate that you

have not entered the code

correctly

– Should the remote con-

trol time-out before you

complete the set-up, you

will need to start over

B. Reassigning

Your Mode Keys To

Another Device

The TV, DVD and AUX keys are

already set up to control spe-

cific devices:

TV key: TV & HDTV

DVD key: DVD

AUX key: VCR, Home

Theater In A Box (HTIB),

Receivers and Amplifiers

You may change these mode

keys to operate another type

of device. To do this, you must

copy an existing mode key

to the one you would like

to change. For example, you

have two DVD players and

you’d like to use the AUX key

for one of them. You would

begin by programming one of

the DVD players into the DVD

mode key and then copy that

to the AUX mode key. Then

you reprogram the original

DVD mode key to the other

DVD player. Before beginning

these steps, program the de-

vice you’d like to copy by fol-

lowing the steps in Section 1.

Then use the steps below to

copy the codes.

1. Press and hold the AT&T

key on the remote control

2. Without releasing the AT&T

key, press and hold the OK

key simultaneously

3. Release both the AT&T key

and the OK key

– All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 944 by pressing the

number keys on the re-

mote control

– All the mode keys will

flash twice indicating cor-

rect entry

5. Press the mode key (i.e.,

TV, DVD or AUX) you

would like to copy the

codes FROM (See above)

– The selected mode key

will flash once

6. Press the mode key you

would like to copy the

codes TO

– The selected mode key

will flash three times in-

dicating successful reas-

signment and return to

normal operations

Once you copy the mode key,

you will have both keys with

the same program code. Now

reprogram the original mode

key with a new code for a sec-

ond device.

Note:

If any other key is pressed ex-

cept the mode keys the AT&T

key will give a long red flash

and the remote control will

return to normal operation.

Should the remote control

time-out before you complete

the procedure you will need

to start over.

4. Resetting to

Factory Defaults

A. Resetting the

Remote Control

to Factory Default

Settings:

1. Press and hold the AT&T

key on the remote con-

trol.

2. Without releasing the

AT&T key, press and hold

the OK key.

3. Release both the AT&T key

and the OK key

– All four mode keys will

flash twice to indicate

programming mode.

4. Enter programming code

900 by pressing the

number keys on the re-

mote control.

– The AT&T key will flash

three times indicating you

have successfully entered

the code and the remote

has been reset to the de-

fault settings

Note:

If any other key is pressed

except the number keys, the

AT&T key will give a long red

flash and the remote control

will return to normal opera-

tion. Should the remote con-

trol time-out before you com-

plete the procedure you will

need to start over.

B. Resetting the

Volume, Channel and

Power Programming:

1. Press and hold the AT&T

key on the remote con-

trol.

2. Without releasing the

AT&T key, press and hold

the OK key.

3. Release both the AT&T key

and the OK key

– All four mode keys will

flash twice to indicate

programming mode

4. Enter programming code

902 by pressing the

number keys on the re-

mote control.

– The AT&T key will flash

three times indicating you

have successfully entered

the code to reset Volume,

Channel and Power to the

defaults and the remote

will return to normal op-

eration

Note:

If any other key is pressed

except the number keys, the

AT&T key will give a long red

flash and the remote control

will return to normal opera-

tion. Should the remote con-

trol time-out before you com-

plete the procedure you will

need to start over.

5. Backlight

Control Set Up

Option

By default the Backlight is set

to ON. You can turn the Back-

light off or on by performing

this function.

1. Press and hold the AT&T

key on the remote control

2. Without releasing the

AT&T mode key, press and

hold the MENU key simul-

taneously

3. Release both the AT&T

mode key and the MENU

key

− All the mode keys will

flash twice indicating pro-

gramming mode

4. Enter 991 by pressing the

number keys on the re-

mote control

− The AT&T mode key will

flash three times indicat-

ing successful toggling

the Backlight enabling/

disabling control.

Note:

− Should the remote control

time-out before you complete

the procedure you will need

to start over.

IFU AT&T IR version 081221.indd 1 12/21/2008 5:13:48 PM

1 2

Manufacture Code List 2

Resumo do Conteúdo

Página 1

AT&T IR U-verse TV Remote Control User GuideInstalling BatteriesThe remote control requires two AA size (1.5V) Alkaline batteries to work.T

Página 2 - Manufacture Code List

Insignia 1507Inteq 1482Janeil 1100JBL 1047, 1053, 1103JC Penney 1000, 1004, 1005, 1007, 1012, 1021, 1048, 1049, 1058, 1063, 1068, 1072, 1073, 1075

Mais documentos para Leitores de CD Radio Shack 3-DVD Changer

Para ver o documento Radio Shack 3-DVD Changer Manual do Proprietário

Radio Shack 3-DVD Changer Manual do Proprietário (28 páginas)

Para ver o documento Radio Shack 3-DVD Changer Especificações

Radio Shack 3-DVD Changer Especificações (32 páginas)

Comentários a estes Manuais

Sem comentários

Radio Shack 3-DVD Changer Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Leitores de CD Radio Shack 3-DVD Changer. Silver Remote Control user guide Manual do Utilizador

Resumo do Conteúdo

Mais documentos para Leitores de CD Radio Shack 3-DVD Changer

Comentários a estes Manuais

Manuais e produtos relacionados com Leitores de CD Radio Shack 3-DVD Changer